How to configure standard access list on Router

How to configure standard access list on router

In this article we will configure standard access list.

In this article we will use a RIP running topology. Which we have created in RIP routing practical.

Download this RIP routing topology and open it in packet tracer
Rip Routing

Because a standard access list filters only traffic based on source traffic, all you need is the IP address of the host or subnet you want to permit or deny. ACLs are created in global configuration mode and then applied on an interface. The syntax for creating a standard ACL is

access-list {1-99 | 1300-1999} {permit | deny} source-address  [wildcard mask]

Three basic steps to configure Standard Access List

• Use the access-list global configuration command to create an entry in a standard ACL.
• Use the interface configuration command to select an interface to which to apply the ACL.
• Use the ip access-group interface configuration command to activate the existing ACL on an interface.

With Access Lists you will have a variety of uses for the wild card masks, but typically For CCNA exam prospective you should be able to do following:

• Match a specific host,
• Match an entire subnet,
• Match an IP range, or
• Match Everyone and anyone

Match specific hosts

Task

Your task is to block 10.0.0.3 from gaining access on 40.0.0.0. While 10.0.0.3 must be able to communicate with networks. Other computer from the network of 10.0.0.0 must be able to connect with the network of 40.0.0.0.

Decide where to apply ACL and in which directions.

Our host must be able to communicate with other host except 40.0.0.0 so we will place this access list on FastEthernet 0/1 of R2 (2811) connected to the network of 40.0.0.0. Direction will be outside as packet will be filter while its leaving the interface. If you place this list on R1(1841) then host 10.0.0.3 will not be able to communicate with any other hosts including 40.0.0.0.

To configure R2 double click on it and select CLI (Choose only one method result will be same)

R2>enable
R2#configure terminal Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#access-list 1 deny host 10.0.0.3
R2(config)#access-list 1 permit any
R2(config)#interface fastEthernet 0/1
R2(config-if)#ip access-group 1 out

OR

R2>enable
R2#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#access-list 1 deny 10.0.0.3 0.0.0.0
R2(config)#access-list 1 permit any
R2(config)#interface fastEthernet 0/1
R2(config-if)#ip access-group 1 out

To test first do ping from 10.0.0.3 to 40.0.0.3 it should be request time out as this packet will filter by ACL. Then ping 30.0.0.3 it should be successfully replay.

PC>ping 40.0.0.3

Pinging 40.0.0.3 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.

Ping statistics for 40.0.0.3:
    Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

PC>ping 30.0.0.3

Pinging 30.0.0.3 with 32 bytes of data:

Request timed out.
Reply from 30.0.0.3: bytes=32 time=140ms TTL=126
Reply from 30.0.0.3: bytes=32 time=156ms TTL=126
Reply from 30.0.0.3: bytes=32 time=112ms TTL=126

Ping statistics for 30.0.0.3:
    Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),
Approximate round trip times in milli-seconds:
    Minimum = 112ms, Maximum = 156ms, Average = 136ms

As we applied access list only on specific host so other computer from the network of 10.0.0.0 must be able to connect with the network of 40.0.0.0. To test do ping from 10.0.0.2 to 40.0.0.3

PC>ipconfig

IP Address......................: 10.0.0.2
Subnet Mask.....................: 255.0.0.0
Default Gateway.................: 10.0.0.1

PC>ping 40.0.0.3

Pinging 40.0.0.3 with 32 bytes of data:

Request timed out.
Reply from 40.0.0.3: bytes=32 time=141ms TTL=126
Reply from 40.0.0.3: bytes=32 time=140ms TTL=126
Reply from 40.0.0.3: bytes=32 time=125ms TTL=126

Ping statistics for 40.0.0.3:
    Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),
Approximate round trip times in milli-seconds:
    Minimum = 125ms, Maximum = 141ms, Average = 135ms

Match an entire subnet

Task

Your task is to block the network of 10.0.0.0 from gaining access on 40.0.0.0. While 10.0.0.0 must be able to communicate with networks .

Wildcards

Wildcards are used with access lists to specify an individual host, a network, or a certain range of a network or networks.

Formula to calculate wild card mask for access list

The key to matching an entire subnet is to use the following formula for the wildcard mask. It goes as follows:
Wildcard mask = 255.255.255.255 – subnet
So for example if my current subnet was 255.0.0.0, the mask would be 0.255.255.255.

255.255.255.255
255 .0 .0    .0       -
----------------
0. 255 .255.255
----------------

Once you have calculated the wild card mask rest is same as we did in pervious example

R2>enable
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#access-list 2 deny 10.0.0.0 0.255.255.255
R2(config)#access-list 2 permit any
R2(config)#interface fastethernet 0/1
R2(config-if)#ip access-group 2 out
R2(config-if)#

To test first do ping from 10.0.0.3 to 40.0.0.3 it should be request time out as this packet will filter by ACL. Then ping 30.0.0.3 it should be successfully replay.

Now do ping from 10.0.0.2 to 40.0.0.3 and further 30.0.0.2 result should be same as the packet is filtering on network based

Match an IP range

You are a network administrator at ComputerNetworkingNotes.com. You task is to block an ip range of 10.3.16.0 – 10.3.31.255 from gaining access to the network of 40.0.0.0

Solutions

Our range is 10.3.16.0 – 10.3.31.255. In order to find the mask, take the higher IP and subtract from it the lower IP.

10.3.31.255
10.3.16.0      -
--------------
0.0.15.255
--------------

In this case the wildcard mask for this range is 0.0.15.255.
To permit access to this range, you would use the following:

R2>enable Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#access-list 2 deny 10.3.16.0 0.0.15.255
R2(config)#access-list 2 permit any
R2(config)#interface fastethernet 0/1
R2(config-if)#ip access-group 2 out
R2(config-if)#

One thing to note is that each non-zero value in the mask must be one less than a power of 2, i.e. 0, 1, 3, 7, 15, 31, 63, 127, 255.

Match Everyone and Anyone

This is the easiest of Access-Lists to create, just use the following:
access-list 1 permit any
or
access-list 1 permit 0.0.0.0 255.255.255.255

Secure telnet session via standard ACL

This is among the highly tested topic in CCNA exam. We could use extended ACL to secure telnet session but if you did that, you'd have to apply it inbound on every interface, and that really wouldn't scale well to a large router with dozens, even hundreds, of interfaces.Here's a much better solution:
Use a standard IP access list to control access to the VTY lines themselves.

To perform this function, follow these steps:

1. Create a standard IP access list that permits only the host or hosts you want to be able to telnet into the routers.
2. Apply the access list to the VTY line with the access-class command

Secure R2 in a way that only 20.0.0.2 can telnet it beside it all other telnet session should be denied

R2>enable
R2#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#access-list 3 permit host 20.0.0.2
R2(config)#line vty 0 4
R2(config-line)#password vinita
R2(config-line)#login
R2(config-line)#access-class 3 in

To test do telnet from 20.0.0.2 first is should be successful.

PC>ipconfig

IP Address......................: 20.0.0.2
Subnet Mask.....................: 255.0.0.0
Default Gateway.................: 20.0.0.1

PC>telnet 50.0.0.2
Trying 50.0.0.2 ...

User Access Verification

Password:
R2>

Now telnet it from any other pc apart from 20.0.0.2. it must be filter and denied

PC>ipconfig

IP Address......................: 20.0.0.3
Subnet Mask.....................: 255.0.0.0
Default Gateway.................: 20.0.0.1

PC>telnet 50.0.0.2
Trying 50.0.0.2 ...

% Connection refused by remote host
PC>